Electrical Products : Product Category

PacSci PowerSync AC

Manufactured by: PacSci (Pacific Scientific)
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Pacific Scientific Synchronous Motors are high torque motors that naturally turn at slower speeds (72 or 60rpm). These high torque 60mm, 90mm, and 110 mm frame size (NEMA 23, 34, and 42) motors are extremely cost-effective and easy to use. They need only a resistor-capacitor (RC) network to operate from single-phase 240vAC power. Other motor technologies (induction, DC, servo, and step motors) need either gear reducers or electronic drives to match the slower speeds of our synchronous motors.
Pacific Scientific Synchronous Motors are powerful and they run smoother, quieter, and cooler than most other AC synchronous motors.

Transtecno AC Motor 1 & 3 Phase

Manufactured by: Transtecno
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

TS and MY series motors are closed and fan cooled.
TS range includes induction three phase 4 poles motors 230/400 Vac at 50 Hz and 275/480 Vac at 60 Hz, it covers power sizes from 0.09 kW up to 3.0 kW. These motors run quietly, they are dynamically well balanced, robust and are an economic solution.

MY range includes induction single phase motors 230 Vac at
50 Hz and covers power sizes from 0.09 kW up to 0.75 kW.
They are particularly suitable for low powered applications. Similar to TS motors, they are robust and are a low cost solution.

Both ranges are made with an aluminum frame and are available with B5 or B14 flange mountings.

Standard features are:

  • Class F thermal insulation
  • IP55 enclosure protection
  • PTO thermostat for overheating protection (only MY)
  • Low noise and vibrations
  • Ambient temperature: -20 °C ÷ +40 °C, without condensing
  • MY series motors have a large terminal box, which includes the run capacitor, protecting it from the external environment.
  • Suitable for heavy and light industrial applications and also for commercial use.

Serapid Linear Beam

Manufactured by: Serapid
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The Serapid Linear Beam is a rodless linear actuator with a thrust capacity of up to 160kN (35,000lbs) and a stroke of virtually any length. It runs fast and smooth, using the robust and reliable Rigid Chain. Working purely mechanically, this actuator is as well suited for the clean-room as for the harsh factory floor, or any other environment. A full range of options allow adaptation to your individual conditions. Heavy duty models are guaranteed over 1 million cycles of full-load, permanent operation.

HaydonKerk Stepper Motor Linear Actuators – Section 2

Manufactured by: HaydonKerk Motion Solutions
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The stepper linear actuator product line offers an effective solution that simplifies the conventional way of translating rotary
into linear motion. The rotary-to-linear conversion is unique; it takes place within the motor itself therefore eliminating the
use of belts and pulleys, rack and pinion and other mechanical components. There’s a detailed tutorial at the beginning of
Section 2 that explains the technology. There are 2 sub-families of stepper motor actuators (Product Summary on page 56)
Hybrid Linear Actuators (Overview on page 75) Footprint: 21 mm to 87 mm (0.8-in to 3.4-in) square Force Output: 2 N to 2200 N (0.5 lb to 500 lb) Linear Travel/step: 1.5 to 127 microns/step (0.00006-in to 0.005-in)/step Can-Stack Linear Actuators (Overview on page 130) Footprint: 15 mm to 46 mm (0.59-in to 1.8-in) diameter Force Output: 7 N to 260 N (1.6 lb to 58 lb) Linear Travel/step: 20 to 400 microns/step (0.0008-in to 0.016-in)/step

Zettlex IncOder

Manufactured by: Zettlex
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Zettlex IncOders are non-contact, absolute angle measuring devices. They use a unique inductive technique and may be considered as an inductive encoder.
IncOders are ideally suited to those applications that require precision measurement in harsh environments where electrical contacts, optical or capacitive devices may prove unreliable.
IncOders have 2 parts –a Stator and a Rotor. Each is shaped like a flat ring.
The large through bore makes it easy to accommodate through shafts, slip rings, optic fibres, through cables etc.
Greater choice of resolutions, up to 26 bit, 0-10V analogue output, digital + 1V sin/cos output option, more options on radial connector, extreme shock and vibration option.
Zettlex – Videos

Chieftek (CPC) Compact Linear Motor Stage

Manufactured by: Cheiftek
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

CLS is a series of structurally compact linear motor modules. It tightly integrates a ironless linear motor, linear guide, optical scale and base. With its zero cogging force, high acceleration, high precision and smooth motion. It is high suitable for in applications such as AOI equipment, laser cutters, pick-place and scanning.

Compared to traditional ball screw modules, CLS series with direct drive coupling provides superior precision and velocity under many thrust output conditions. At the same time providing the same highly integrated mechanical design. Enabling increased productivity and reliability as a direct replacement.

Kollmorgen Electric Cylinder

Manufactured by: Kollmorgen
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Kollmorgen Electric Cylinders offer a cost effective solution for linear positioning of supported or pivoting loads. They are descendents of hydraulic or pneumatic cylinders with many of the same design features but offer the benefit of pr viding a simpler and cleaner transmission.
When high thrust is required these rod type cylinders have the advantage over other linear components because the thrust is transmitted in-line. They also have the advantage of being isolated from the work area so can retract during other operations.
Flexibility in mounting allows either rigid or pivoting options depending on the requirement of the application. In addition to mounting options a wide variety of servo and stepper motor and drive products are offered as an integrated solution to provide the most cost effective combination of thrust, speed and positioning accuracy for your application.

Zettlex LinTran Linear Position Transducers Product Guide

Manufactured by: Zettlex
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Zettlex LINTRAN transducers are non contacting, absolute, linear position measuring devices. They utilise a unique inductive technique and comprise two main components a Target and a Stator. The Stator is longer than the Target and is powered with an electrical supply and can be moving or stationary. An electrical output from the Stator shows the position of the Target relative to the Stator. The Target has no electrical connections and can be moving or stationary.

Zettlex LINTRAN encoders are sealed to IP57 so they are ideally suited to harsh environments where electrical contacts or optical transducers would prove unreliable. The LINTRAN range offers a cost effective alternative to LVDTs, magnetostrictive devices or precision potentiometers. LINTRAN units do not require precision mounting and are field programmable without a PC.

Zettlex – Videos

MOONS’ Step Servo EtherCAT Drive

Manufactured by: MOONS'
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The SS-EC is a member of the Step-Servo family equipped with a built-in EtherCAT communication interface. This drive can operate as a standard EtherCAT slave using CANopen over EtherCAT (CoE). It is designed to work with various MOONS’ Step servo motors.

  • Programmable, digital step-servo drive and motor package
  • Operates from a 24 to 70 volt DC power supply
  • CANopen over EtherCAT (CoE) with full support of CiA402. Based on the widely used 100BASE-TX cabling system and with a baud rate of 100Mbps full duplex, EtherCAT enables high speed and highly reliable communication
  • Support modes: Profile Position, Profile Velocity, Profile Torque, Cyclic Synchronous Position, Cyclic
    Synchronous Velocity and Homing; as well as MOONS’ own Q mode
  • Dual port EtherCAT communication
  • USB port for configuration
  • Encoder resolution: 20000 counts/rev for AM17/23/24/34SS motor, 4096 counts/rev for AM11SS motor
  • SS03-EC output current: continuous 3A, boost 4.5A
  • SS05-EC output current: continuous 5A, boost 7.5A
  • SS10-EC output current: continuous 10A, boost 15A
  • 8 optically isolated digital inputs, 5-24VDC high level voltage
  • 4 optically isolated digital outputs, max 30V/100mA sink or source current
  • 2 analog inputs, can be configured to 0-5V, 0-10V, ±5V or ±10V signal ranges
  • Differential encoder signal output (AOUT+/-, BOUT+/-, ZOUT+/-), 26C31 line driver, 20mA sink or source current
  • Auxiliary power supply for keep alive operation
  • Front panel with 4 keys and 5 digital LED display for setting parameters
  • STO function (Safe Torque Off)

LinMot P04 Linear Motor

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

At this year’s SPS IPC Drives conference, LinMot presents the newly developed model P04 linear motor. This motor has all the benefits of the familiar tubular linear motor and the additional advantage of an integrated linear guidance. The P04-actuator can be equipped with mechanical accessories which are known from pneumatics.

LinMot Cost Optimisation for Linear Motor

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

GREATER FLEXIBILITY AND DYNAMICS
Especially when more than two positions are required, when positions need to be changed by software, when motions are synchronized to a main drive, or when the dynamics and service life of a pneumatic cylinder are simply not sufficient, designers gladly turn to linear direct drives from LinMot.

SIMPLE START-UP
By integrating the control of position, speed, acceleration, and force, commissioning is made much easier. Motion parameters are
calculated when the project is laid out, and can be adopted directly during commissioning.

IMPROVED PROCESS STABILITY
Unlike pneumatic cylinders, where only the end positions are checked, the position of a linear motor is constantly controlled and monitored. This leads to much greater process stability, because very small deviations can be detected when needed.

REPLACEMENT PAYS OFF EVEN FOR SIMPLE MOTIONS
Due to high operating costs for pneumatics, the use of industrial linear motors pays off to an increasing degree, even for simple point-to-point motions with only two end positions. This is especially true when motions are performed regularly in cyclical operations, and pneumatic cylinders need to be oversized due to speed and load conditions. In this case, the energy and maintenance costs exceed the investment costs within a few weeks (see example, right).

SIMILAR CONFIGURATION MAKES REPLACEMENT EASY
Industrial linear motors have a cylindrical form factor and similar dimensions to pneumatic cylinders. For this reason, they are commonly used as replacements for pneumatic actuators in existing and new designs.

ADVANTAGES OF INDUSTRIAL LINEAR MOTORS

  • Freely positionable
  • Extremely dynamic
  • Long Service Life
  • Adjustable speed
  • Monitored motions
  • Low maintenance costs
  • Adjustable acceleration
  • Gentle motions
  • Hygiene (no air)
  • Programmable force
  • Synchronization capability
  • Low energy costs

LinMot Bottle Closure Application

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

LinMot linear rotary motors have been developed for closure and screwdriving processes, allowing flexible closure and
screwdriving processes to be implemented easily.

  • One physical axis with independently programmable linear and rotary motions
  • Open parameterization of positions, linear speed, rotary speed, force, torque
  • Readout of torque, rotary speed, angle, vertical position, linear speed, and force
  • Can be integrated in any control system

LinMot Product Family Overview

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

In the products and in the everyday life of NTI AG, these values are inseparable.
NTI AG is a global manufacturer of high quality tubular style linear motors and linear motor systems and thus focuses on the
development, production and distribution of linear direct drives for use in industrial environments. Founded in 1993 as an independent business unit of the Sulzer Group, NTI AG has been in operation since 2000 as an independent company.
NTI AG headquarters are located in Spreitenbach, near Zurich in Switzerland. In addition to three production sites in Switzerland and Slovakia, NTI AG maintains a sales and support office LinMot® USA Inc. to cover the Americas.
The brands LinMot® for industrial linear motors and MagSpring® for magnetic springs are offered to customers worldwide. NTI AG maintains an experienced customer consultant sales and support network of over 80 locations worldwide.
For the realization of linear motion NTI AG is always a competent and reliable partner.
Mission

LinMot offers its customers a sophisticated and dedicated linear drive system that can be easily integrated into all leading control systems. A high degree of standardization, delivery from stock and a worldwide distribution network insure the immediate availability and excellent customer support. Our aim is to push linear direct drive technology and make it a
standard machine design element. We offer highly efficient drive solutions that make a major contribution to the overall resource conservation effort.

LEA3 Series Actuator

Manufactured by: Various
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Small industrial actuators, low cost, double clevis mount, 12 and 24vDC, up to 750N thrust, up to 300mm stroke, up to 45mm/sec travel rate, IP65 sealing option, potentiometer feedback option. Available from stock.

Thomson Linear Lifting Columns

Manufactured by: Thomson Linear
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • Designed for domestic, office and medical applications
  • Self supporting column in extruded anodized aluminum
  • Low weight and quiet operation
  • Smooth operating telescopic screw drive
  • High load torque capability
  • Very short retracted length
  • Very low stroke to retracted length ration
  • Maintenance free
  • Dynamic braking and load holding brake
  • Integrated end of stroke limit switches
  • EMC recognized for medical applications

LinMot Miniature Linear Servo Drives

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

These are dynamic miniature direct linear drives in tubular ironless construction! The very compact size is suitable for applications with lac of space. Linear modules are ready to use linear guides with integrated linear motors. Build with precise ball sliders and rails, high force and torque loads are available. Maximum speed and acceleration refer to the linear motor data. A wide variety of motion controllers offer the choice for best fitting to the application. Fieldbus devices with Profibus-DP, CANOpen, DeviceNet, RS232, RS485 and Ethernet are available.

Kollmorgen Linear Positioners

Manufactured by: Kollmorgen
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Kollmorgen offers electric cylinder drive mechanisms designed around either lead screws or ballscrews. Ballscrews, being the more efficient of the two, utilize ballnuts riding on recirculating ball bearings resulting in higher speeds, loads and cycle rates.
Electric Cylinders are preferred when:

  • Positioning an externally guided and supported load,
  • Moving a load that pivots,
  • There is a high concentration of airborne contaminants (rodless positioners are inherently less well protected),
  • Replacing a hydraulic or pneumatic cylinder with an electro-mechanical solution,
  • Brushless Servo with encoder or resolver feedback,
  • Stepper motors are also available,
  • Thrust up to 25000 N [5620 lb], and
  • Speed up to 1.3 m/s [52.5 in/s]

Dart Controls Electronic Motor Speed Controls

Manufactured by: Various
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • SCR and Digital DC speed controls for AC line voltage to 3HP,
  • Brushless DC speed controls,
  • Battery operated DC speed controls,
  • AC inverter drives to 5hp,
  • Open and closed loop control systems,
  • Digital tachometer for rate and time,
  • Speed sensors,
  • Variable AC voltage supply, and
  • Standard stock DC motors

Rodless Actuators

Manufactured by: Thomson Linear
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • For use in domestic, office or medical applications
  • Rigid self supporting extruded aluminum profile
  • Durable and corrosion free
  • Holding brake prevents downward motion at power off
  • Lightweight and quiet operation
  • Safety nut on ball screw versions
  • Easy and fast T-slot mounting
  • Optional spline safety function
  • Maintenance free

Kollmorgen AKD Servo Drive

Manufactured by: Kollmorgen
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The AKD servo drive delivers cutting edge technology and performance with one of the most compact footprints in the industry. These feature rich drives provide a solution for nearly any application, from basic torque and velocity applications, to indexing, to multiaxis programmable motion with embedded Kollmorgen Automation Suite. The versatile AKD sets the standard for power density and performance.

ELAP Linear Motion Potentiometers Series PL231

Manufactured by: ELAP SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Linear motion potentiometers change mechanical linear moves into the corresponding electrical signals. Accurate, stout and reliable, they solve any problem linked to measuring and positioning control on any kind of industrial machine. Thanks to their small size, they can be profitably employed for those applications where limited dimensions are a critical factor.

Fulling Brushless DC Motors

Manufactured by: Fulling Motors
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The differences between a DC motor having a mechanical commutation system and a BLDC motor are mainly found in:

  • the product concept
  • the commutation of phase currents
  • from the user’s point of view, brushless DC motors follow the same equations as those with brushes: torque is proportional to current, speed depends on the voltage and the load torque

Chieftek (CPC) Linear Motors

Manufactured by: Cheiftek
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • CPC linear motors are designed with overlapping coils to provide high force density
  • CPC uses a vacuum-molding process to eliminate air bubbles from the finished epoxy mold. This results in strengthened epoxy product that will enhance its lifetime
  • CPC linear motors are designed to have stable system
  • CPC linear motors are very efficient at dissipating waste heat, resulting in the ability to receive and utilize large currents for an increase in power

Kollmorgen Cartridge DDR (Direct Drive Rotary

Manufactured by: Kollmorgen
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The Cartridge DDR motor is the newest addition to the Kollmorgen line of DDR products. The Cartridge DDR motor does not have bearings and it mounts to a machine using the machine’s existing bearings to support the motor’s rotor. The frame of the Cartridge DDR motor mounts to a pilot and bolt circle on the machine frame much like a conventional motor. The rotor engages to the load using an innovative compression coupling, which effectively makes the motor’s rotor and the load one piece, eliminating any compliance between the motor and the load.

  • Torque to 1090Nm
  • Speed to 2500rpm

DC Power Supplies

Manufactured by: Various
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • Specifically designed to power stepping and servo drivers
  • Efficient switch mode designed
  • Output power up to 300W
  • Short circuit, over-voltage protection
  • Input voltage 220VAC or 110VAC (optional)
  • Simple operation
  • Compact size, lightweight

Gimatic Magnetic Sensors

Manufactured by: Various
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The magnetic sensor is a device that change its status with the magnetic field. Basically it’s used as proximity end-stroke on the pneumatic cylinders which have the piston holding a magnet.

HaydonKerk Sealed Switches

Manufactured by: HaydonKerk Motion Solutions
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Haydon’s sealed switches are used in commercial jets, military aircraft, military ground equipment, space applications and industrial applications with harsh environmental conditions, such as gas turbines and high temperature research instrumentation. Haydon switches are built to meet stringent military specifications.
To achieve and sustain such high levels of quality requires a combination of skilled engineering and production teams, special support facilities and coordinated quality control from design through production. Haydon has all of these factors in place and, because of this, our switches are recognized for their quality and robustness by engineers throughout the world.

Deltran Brake & Clutch

Manufactured by: Deltran division of Thomson Linear
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • Clutch and Brake Technologies – We offer Electro-magnetic Friction Clutches and Brakes.
    See our full line catalogue for product specifications and operation; design and application examples, plus engineering guidelines
  • Selection by Motion Type – The Selection Chart by Motion Type identifies our standard products by the basic motions of START, INDEX, SLIP, STOP and HOLD. Each of these motion types are noted by an icon on the left side of this chart.
    If you know that your application requires a specific motion, this chart may be a helpful place to start your clutch and brake selection.

Rollon Uniline System

Manufactured by: Rollon SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Uniline is a family of ready-to-install linear actuators. They consist of internal Compact Rail roller sliders and steel-reinforced polyurethane belts in a rigid aluminum profile. Longitudinal seals enclose the system. This arrangement provides the best protection for the actuator from soiling and damage. In the A series, the fixed bearing rail (T-rail) is mounted horizontally
in the aluminum profile. Versions with long (L) or double (D) sliders in one axis are possible.
The most important characteristics:

  • Compact design
  • Protected internal linear guides
  • High traversing speeds
  • Grease-free operation possible (depending on the application. For further information, please contact our Application Engineering department)
  • High versatility
  • Long strokes
  • Versions with long or multiple sliders available in one linear axis

Preferred areas of application:

  • Handling and automation
  • Multi-axis gantries
  • Packaging machines
  • Cutting machines
  • Displaceable panels
  • Painting installations
  • Welding robots
  • Special machines

Technical data:

  • Available sizes [mm]:
    Type A: 40, 55, 75, 100
  • Length and stroke tolerances:
    For strokes <1 m: +0 mm to +10 mm (+0 in to 0.4 in)
    For strokes >1 m: +0 mm to +15 mm (+0 in to 0.59 in)

LinMot Catalogue

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The LinMot system features are designed for:

  • Replacements for pneumatic cylinder and linear servo applications where higher speeds, acceleration ,positioning and holding are required
  • Simplicity with only one moving part
  • Are all stainless steel and will suit very harsh and wet environments ( IP67 )
  • Stroke lengths from 50mm to 1460mm
  • Speeds up to 3 m/sec
  • Repeatability to +/- 0.05mm with base unit straight out of the box or +/- 0.001mm with external position sensor
  • Accelerations to 400 m/s2 and forces to 585N (1200N model coming) with outstanding user-friendly programmability, accuracy and inter-connectivity.

Zettlex IncOder

Manufactured by: Zettlex
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Zettlex IncOders are non-contact, absolute angle measuring devices. They use a unique inductive technique and may be considered as an inductive encoder.
IncOders are ideally suited to those applications that require precision measurement in harsh environments where electrical contacts, optical or capacitive devices may prove unreliable.
IncOders have 2 parts –a Stator and a Rotor. Each is shaped like a flat ring.
The large through bore makes it easy to accommodate through shafts, slip rings, optic fibres, through cables etc.
Greater choice of resolutions, up to 26 bit, 0-10V analogue output, digital + 1V sin/cos output option, more options on radial connector, extreme shock and vibration option.
Zettlex – Videos

Rotary Limit Switch TER General Catalogue

Manufactured by: TER
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Rotary Limit Switches designed with the requirements of a more demanding market, where quality is the key to success. The combination of a wide range of reduction ratios and the small size of the unit makes these new switches advanced in their field. The availability of 4 different types allows customers to choose the best ratio between cost and performance, according to their particular needs.

Variable AC

Manufactured by: Oemer Motor
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

There are many manufacturers of VSD’s available on the Australian market. Motion Technologies use this class of drive to compliment our range of servo and stepper BLDC drives.

Also, Vector drives are closely aligned to VSD’s except they include feedback devices and generally used for high power motors like Oemer Motors, see below catalogue.

Rollon Plus System

Manufactured by: Rollon SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

TH linear actuators are rigid and compact, ball screw driven linear units, that enable high positioning accuracy and repeatability in all process phases. With optimal performance assured, TH actuators have a repeatability within 5 μm.
Thrust force transmission is achieved by means of super high efficient ball screws, which are available in several precision classes and a variety of leads. Linear motion is based on two or four preloaded re-circulating ball bearing blocks, with ball retainer technology, mounted on two precision aligned parallel rails. The TH series is available in single carriage or double
carriage versions to meet different load requirements.
The TH linear units also feature safe rail and screw lubrication through a dedicated channel for each component. The incredibly compact structure of the TH actuator makes it the ideal solution for applications where space is limited.

  • Extremely compact dimensions
  • High positioning accuracy
  • High load capacity and stiffness
  • Preloaded ball screw
  • Block with ball retainer
  • Internal protected rails and ball screw
  • Safe lubrication through dedicated channels for each component (block and ball screw)

MOONS’ TSM Integrated Step Servo

Manufactured by: MOONS'
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The Step-Servo is an innovative revolution for the world of stepper motor, it enhances the stepper motors with servo technology to create a product with exceptional feature and broad capability.
TSM is MOONS’ 3rd generation integrated Step-Servo and compact motor+drive+encoder+controller all-in-one solution. With improved technology, TSM upgrades significant key fearures based on 2nd generation SSM and operates more efficient and intelligent.

Golden Motors Brushless Low Voltage DC Motor 7.5KW

Manufactured by: Golden Motors
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

HPM5000B and HPM7500B series”

  • Voltage ratings: 48, 72, 96 Vdc
  • Rated DC bus current: 30 to 200 Amps
  • Rated power:
    Up to 5kW air cooled (5000 series)
    Up to 7.5kW liquid cooled (7500 series)
  • Phase resistance (mOhm): 6.2@48V, 12.0@72V, 36.0@120V
  • Phase Inductance (μH): 68@48V, 154@72V, 504@120V
  • Cooling: Air (inbuilt fan) or fluid (water, oil, etc)
  • Efficiency: 91%
  • Speed limit: Up to 6000 rpm (model & winding dependant)
  • Weight: 11kg
  • Housing Material: Aluminium
  • Output shaft material: Stainless steel
  • Housing dimensions: Ø126mm X 206mm long
  • Shaft dimensions: Ø22 X 53mm long, with 5mm sq. keyway
  • Options on request:
    Rear shaft extension (eg, water pump drive, tacho, encoder)
    Custom speed and voltage
  • Application examples:
    Electric car, golf buggy, motorcycle, tricycle, boats of all
    types, forklift truck, recreational buggy, outboard motors, ROV, bicycle, wheelchair
  • Model Number example:
    HPM7500B/48L = 7.5kW, 48Vdc, liquid cooled ratings

Rollon Tecline

Manufactured by: Rollon SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Our tecline linear system range is suitable for the handling of loads from 10 up to 1000 kg, by manufaturing one or more axis systems according to the customer requirements.
Our main application fields are: robotics, palletization, production line, logistics and manufacturing machines with Cartesian axis movements.
Our products stand out for their:

  • easy and quick assembly
  • high quality and competitive performances (profiles up to 12 m)
  • reduced and simplified maintenance
  • wide range of integrated solutions
  • possibility of customised solutions
  • constant technical support and CAD drawings available

Our Tecline linears strong points are:

  • Solid beams obtained from aluminium alloy extruded profiles
  • High-performance aluminium casting alloy plate and preset for tool assembly
  • Adapting plate suitable for any commercial available gearboxes
  • Fixed and oscillating roller slides, which can be adjusted through an eccentric bushing
  • Without play and sealed rollers with a “for life” lubricating system
  • Tempered or induction hardened and machined strong V-shaped steel guide rails
  • Adjustable limit stops provided with rubber buffers
  • Wide range of accessories for 3 or more axis linears

Rollon Modline

Manufactured by: Rollon SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Modline linear modules are ready-to-use linear guide systems with high accuracy, speeds and load performances.
Our experience in the fields of the automotive plants, painting, plate working, manufacturing machines and palletization
systems has allowed us to widen our product range with the most advanced technical solutions.
Our products stand out for their:

  • high quality and competitive performances (profiles up to12m)
  • without play transmissions achieved by high torque couplings
  • beams with transversal stiffening ribs and preset for threads on profile ends
  • accurate scaling and consequent reduced maintenance
  • fast and accurate belt or without play screw drives
  • the most complete range of accessories
    The Modline linear module strong points are:
  • Acomplete series of linear units to build up 3 or more axis cartesian robots
  • Linear modules with linear guides suitable for parallel assembling
  • Choice between strong steel linear guides with rollers or accurate caged ball roller slides and guides
  • Choice between mobile carriage or fixed carriage and mobile profile
  • Wide and complete solutions for control systems programmable cards on request
  • On request: assembling of E-chain cable carriers, reduction units, stiffening angle bars
  • Drawing worked carriage plates
  • Accessories and compatibility for pinion/rack drive unit integrated assembling

Rollon Sys

Manufactured by: Rollon SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The Sys linear transfer system consists of higher mechanical performances aluminium alloy rail with deepanodising surface and light alloy extruded roller slides.

  • extremely small section sizes
  • modularity of the system achieved by structural
  • profiles and wide range of accessories
  • special profile section to protect sliding tracks and roller
  • slow friction lame contact roller
  • high resistance polyamide roller surface
  • customizable solutions for the applied loads

Applications such as handling units, Cartesian robots and lift and shift systems are implemented in the following sectors: wood working industry, body in white welding lines, white goods industry, piping
and sheet metal working industry.

Attached Files:
MT-Rollon-Sys-281015.pdf

Serapid RigiBelt Linear Telescopic Actuator

Manufactured by: Serapid
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Serapid, the leader in mechanical lifts and telescopic actuators based on its Rigid Chain Technology, introduces a non magnetic actuator. The RigiBelt has two belts which come together like a zipper to form a rigid column.
The belts of the RigiBelt are made of reinforced plastic and therefore are entirely non magnetic. It moves smoothly while telescoping in and out of its drive.
All of Serapid’s linear telescopic actuators are entirely mechanical, which make them environmentally friendly and suitable for clean-room conditions. East system has suitable configuration and can be customized as needed.
The RigiBelt has non corrosive properties, and is compact and adaptable. It is able to fit into any product or machine.

Panasonic AC Servo A5

Manufactured by: Panasonic
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Advanced range of servo motors and drives from 50 watt to 15kw. Used for all types of automation for robots, process machinery, packaging and factory automation. They feature 23 bit high resolution encoders, IP65 or IP67, high speed response and settling, small and compact.

Click here to view CAD downloads

Trio Product Brochure

Manufactured by: Trio Motion Technology
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Trio Motion Technology’s range of motion controllers, daughter boards, I/O modules and keypads are designed to enable the control of industrial machines with the minimum of external components.
In many applications, Trio’s range can be combined to build a control system capable of driving a multi-axis machine and all its auxilliary equipment.
A single programming interface that is scalable from a single axis up to 64 axis coordinated motion.

Functions include:

  • Linear, Circular, Helical and spherical interpolation
  • Variable speed/acceleration profiles
  • Electronic gearboxes
  • Electronic cam profiles generate motion based on the position of another axis or based on time
  • Superimpose multiple moves/cam to generate the final motion
  • High Speed Registration; ideal for adding motion into continuous processes
  • Communication function enabling interface to HMI or SCADA type systems
  • 64bit, 400MHz MIPS processor with 200MHz DDR memory allows quicker program execution

ELAP Encoder EtherCAT

Manufactured by: ELAP SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Based on the industrial Ethernet communication protocol, the EtherCAST interface is steady, flexible and fast, therefore particularly suitable for communication between control systems and peripheral devices, such as I/O systems, drives, sensors and actuators.

MEM-BUS EtherCAT encoders offer:

  • Real time communication
  • Flexible number of nodes
  • Easy installation and maintainance
  • Net topologies configuration
  • Automatic slaves addressing
  • Flexible work ranges programming

MOONS’ SR Series Two Phase

Manufactured by: MOONS'
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

SR Series Two Phase DC Stepper Motor Drives with DC Input, DIP and Rotary Switch setting, Pulse & Direction Control Drive. They are cost-effective, high performance step drives. The design is based on advanced digital current control technology and features high torque, low noise and low vibration. The running current, microstep resolution and other parameters are switch selectable.

  • Settable current from 0.3 to 7.8 amps
  • Supply voltage 12 to 75 VDC
  • Advanced Current Control
  • Torque Ripple Smoothing
  • Anti-Resonance
  • Microstep Emulation

Super-Jack Linear Actuator IJ Series

Manufactured by: Various
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Commercial grade, cost effective linear actuators, medium duty, AC or DC motors, thrusts to 7000N, strokes to 1220mm, in-built limit switches. Available from stock.

 

 

Pneumatic Telescopic Masts

Manufactured by: Various
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

  • Pneumatic Telescopic Masts, widely used in; antenna’s, mobile lighting, military, flag masts etc,
  • Locking and Non-Locking collar’s available, and
  • Cabling option available

Thomson Linear Actuators

Manufactured by: Thomson Linear
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Precision linear actuators are used in handling, machining and manufacturing applications. Another suitable area is in the replacement of hydraulic or pneumatic cylinders where they bring many benefits compared to these traditional technologies. The broad range of options and accessories and our long experience in building customised units makes it easy to find the perfect actuator for almost any application.

LTN Frameless Resolvers

Manufactured by: LTN Servotechnik
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Operating temperature -55ºC … +155ºC. Permissible speed: 20,000rpm maximum. Accuracy absolute: ±4′ / ±6′ / ±10′.
Accuracy ripple: 1′ maximum. Rotor and stator completely impregnated. 1/2/3/4 pole pairs.

ELAP HPS Linear Wire Potentiometer

Manufactured by: ELAP SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The transducer consists of a rotary potentiometer operated by means of a wire-reel mechanism; the wire is out of stainless steel covered with nylon. The potentiometer provides an analogue signal proportional to the linear displacement of the wire. The inside spring controls the return of the wire to the starting position.

LinMot MagSpring

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

MagSpring products can best be described as “magnetic springs”. The term “spring”, however, is to be understood to mean that MagSpring components generate a constant force over their entire working range, while the characteristic curve for a typical mechanical spring shows an increase in force with increasing displacement. The generation of force that is independent of the stroke makes MagSpring preferable for balancing weight forces in vertical drive applications.

Transtecno Permanent Magnets DC Electric Motors

Manufactured by: Transtecno
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The main features of the brushed EC motor range are:

  • Magnetic field generated by permanent magnets
  • Tubular construction, without fan
  • Available in 5 sizes: diameter 42, 52, 65, 81, 110mm
  • Low voltage power supply, 12 or 24 Vdc
  • Power ratings available from 30 to 800 W S2
  • High starting torque
  • High torque and output power with compact package

Kollmorgen AKM Motor Selection

Manufactured by: Kollmorgen
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The advanced Kollmorgen AKM high performance motor series offers a wide range of mounting, connectivity, feedback and other options. These motors offer superb flexibility to meet application needs. This series covers 7 frame sizes, 25 frame/stack combinations, 77 ‘standard’ windings, 0.16 to 53Nm, up to 8000rpm.

LinMot Catalogue

Manufactured by: LinMot
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The LinMot system features are designed for:

  • Replacements for pneumatic cylinder and linear servo applications where higher speeds, acceleration ,positioning and holding are required
  • Simplicity with only one moving part
  • Are all stainless steel and will suit very harsh and wet environments ( IP67 )
  • Stroke lengths from 50mm to 1460mm
  • Speeds up to 3 m/sec
  • Repeatability to +/- 0.05mm with base unit straight out of the box or +/- 0.001mm with external position sensor
  • Accelerations to 400 m/s2 and forces to 585N (1200N model coming) with outstanding user-friendly programmability, accuracy and inter-connectivity

Kollmorgen Housed DDR Motor Selection Guide

Manufactured by: Kollmorgen
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Our Housed Direct Drive Rotary (DDR) motor series offer a high performance, zero maintenance servo solution. They achieve very high torque density through the combination of large diameter, short length, and a high number of magnetic poles.
By pairing the Housed DDR motor series with our wide range of plug-andplay Ethernet-based AKD™ servo drives, you can optimize performance and increase the machine’s overall effectiveness. The DDR motor can be used as a flexible indexer, providing programmable, rapid, indexing far exceeding the throughput of conventional mechanical or variable reluctance technology indexers. It can also be used for replacing mechanical transmissions such as gearboxes, timing belts, and rack and pinion reducers.

  • Torque range from 5.3Nm to 339Nm continous
  • Speeds from 500 to 120rpm

Serapid Horizontal Chains

Manufactured by: Serapid
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

SERAPID push systems provide a mechanical way to move horizontal heavy loads. Just like the vertical lift systems, this is based on the locking and unlocking of flexibly connected, linked elements. When pushing a load, the specially shaped chain links interlock with each other, forming a rigid bar or column. When lowered, the links unlock, allowing it to remain flexible. The chain bends or coils into a compact package.

Columbus McKinnon Phoenix Telescopic Lifting Column

Manufactured by: Pfaff-silberblau
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The “PHOENIX” telescopic lifting column is a compact lifting system with integrated guiding arrangements made of high-quality, anodized precision aluminium profiles, worm gear screw jacks from the MERKUR range and a directly mounted motor. They can be used independently or as a complete lifting system. Synchronisation can be effected electric or via a mechanical connection by means of articulated shafts. Loads to 25,000N, 1000mm stroke.

Rollon Eco System

Manufactured by: Rollon SpA
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The ECO SYSTEM units are linear actuators made of a self-supporting extruded aluminum frame and are driven by a polyurethane belt with AT metric profile steel inserts.

  • Three different sizes available: 60mm, 80mm, 100mm
  • Version available with recirculating ball bearing or roller rails
  • Reduced weight ensured by the light frame and the aluminum sliders
  • High sliding speed

The ECO SYSTEM series actuators are offered with two motion systems:
ECO SYSTEM – SP
Featuring a maintenance free recirculating linear guide rail fitted inside the profile.
ECO SYSTEM – CI
Featuring four rollers with a Gothic arch outer profile sliding on hardened steel bars placed inside the profile.

Copley Selection Guide

Manufactured by: Copley Controls
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Copley Controls any servo motor for any application and any environment. The Copley range of AC and DC servo drives allows for direct PC control of multi-axis applications with seamless connectivity. Copley supports various modes of communications including CANopen and EtherCat. All drives are Safety enabled with Safe Torque Off mode certified to international standards and support all encoder and resolver types. The R-Series is also available for applications requiring a ruggedized drive with specially designed drives to withstand extreme temperatures from -40 to 70 degrees C and high vibration environments up to 500 Hz. With Copley’s complete range of drives you’re guaranteed to find the ideal servo drive for your application.

MOONS’ Integrated Stepper Motor

Manufactured by: MOONS'
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Anti-Resonance

Step motor systems have a natural tendency to resonate at certain speeds. The STM drive+motor automatically calculates the system’s natural frequency and applies damping to the control algorithm. This greatly improves midrange stability, allows for higher speeds, greater torque utilization and also improves settling times.

Microstep Emulation

With Microstep Emulation, low resolution systems can still provide smooth motion. The drive can take low-resolution step pulses and create fine resolution micro-step motion.

Torque Ripple Smoothing

All step motors have an inherent low speed torque ripple that can affect the motion of the motor. By analyzing this torque ripple the system can apply a negative harmonic to negate this effect, which gives the motor much smoother motion at low speed.

Command Signal Smoothing

Command Signal smoothing can soften the effect of immediate changes in velocity and direction, making the motion of the motor less jerky. An added advantage is that it can reduce the wear on mechanical components. Allows for three current settings to help the motor run cooler and reduce power consumption.

  • Running Current – the current the drive will deliver for continuous motion.
  • Accel Current – the current the drive will deliver when accelerating or decelerating.
  • Idle Current – reduces current draw when motor is stationary.

Self Test & Auto Setup

At start-up the drive measures motor parameters, including the resistance and inductance, then uses this information to optimize the system performance.

Panasonic Minas A5B

Manufactured by: Panasonic
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

Click here to view CAD downloads

  • Frequency response: 2300Hz
  • Supports network communication “EtherCAT”
  • High-speed 100Mbps
  • Real-time auto tuning function, anti-vibration filters are available
  • EtherCAT with many supported application
  • System-up possible with various slaves
  • Supports PC-based controller
  • Smallest EtherCAT drive in market
  • Supports pc setup software “Panaterm”
  • Passed official EtherCAT conformance test
  • IEC safety I/F model available

Trio MC4N-ECAT Mini EtherCAT Master

Manufactured by: Trio Motion Technology
Sold and Serviced by Motion Technologies Pty Ltd. Ph +61 2 9524 4782.

The MC4N is a new concept in high performance Motion Coordinators which is dedicated to running remote servo and stepper drives via the EtherCAT real time automation bus. It is based on an up-rated version of the 532MHz ARM 11 processor which makes it ideal for high axis count machines or robotic applications.